ОКС/МКС

01 - Общие положения. Терминология. Стандартизация. Документация

01.040 - Словари

01.040.21 - Механические системы и компоненты общего назначения (Словари)

21 - Механические системы и устройства общего назначения

21.220 - Гибкие приводы и передачи

21.220.10 - Ременные приводы и их компоненты

История замен документа
Принявший орган
Госстандарт СССР
Дата принятия
30.03.1990
Дата вступления в силу
01.07.1991
Действует c 01.07.1991

ГОСТ 28500-90

Передачи ременные синхронные. Термины и определения (ИСО 5288-82)

       

     ГОСТ 28500-90

(ИСО 5288-82)

 

Группа Г00

 

      

     

МЕЖГОСУДАРСТВЕННЫЙ СТАНДАРТ

 

 

 ПЕРЕДАЧИ РЕМЕННЫЕ СИНХРОННЫЕ

 

 Термины и определения

 

 Synchronous belt drives. Terms and definitions

     

МКС 01.040.21

        21.220.10

ОКСТУ 0090; 4101

Дата введения 1991-07-01

 

      

     

ИНФОРМАЦИОННЫЕ ДАННЫЕ

ВНЕСЕН Министерством нефтеперерабатывающей и нефтехимической промышленности СССР

 

Постановлением Государственного комитета СССР по управлению качеством продукции и стандартам от 30.03.90 N 721 введен в действие государственный стандарт ГОСТ 28500-90, в качестве которого непосредственно применен международный стандарт ИСО 5288-82 с 01.07.91

 

ПЕРЕИЗДАНИЕ. Октябрь 2005 г.

 

 

 1. ОБЪЕКТ И ОБЛАСТЬ ПРИМЕНЕНИЯ

Настоящий стандарт устанавливает термины и определения понятий в области синхронных ременных передач.

 

Термины, установленные настоящим стандартом, обязательны для применения во всех видах документации и литературы, входящих в сферу работ по стандартизации или использующих результаты этих работ.

 

В таблице приведены термины с определениями на трех официальных языках ИСО - русском, английском и французском.

 

В таблице к ряду терминов приведены буквенные обозначения и чертежи.

 

В стандарте приведены алфавитные указатели содержащихся в нем терминов на английском, французском и русском языках. Кроме того, в качестве справочных приведены алфавитные указатели терминов-эквивалентов на немецком и итальянском языках.

 

Термины и определения, относящиеся к синхронным ременным передачам

     

     

Таблица

 

 

 

 

 

 

Термин

Обозна-

чение

Определение

Чертеж

2 General definitions

 

 

Общие определения

 

 

 

 

 

 

 

2.1 synchronous belt drive

 

 

A system composed of a synchronous belt and two or more synchronous pulleys. Synchronized motion and/or power is transmitted through the engagement of teeth on the belt with teeth on the pulleys

 

 

transmission par courroie synchrone

 

 

 
d’une courroie synchrone et d’au moins deux poulies synchrones. La rotation
ou la puissance est transmise par
des dents de la courroie avec celles des poulies
 

 

 

синхронная ременная передача

 

 

Передача, состоящая из синхронного ремня и не менее двух синхронных шкивов; мощность или вращение передаются посредством зацепления зубьев ремня с зубьями шкивов

 

 

2.2 centre distance

 

The shortest distance between the axes of two synchronous pulleys when the belt is under the prescribed measuring force

 

entr’axe

 

Plus courte distance entre les axes de deux poulies synchrones lorsque la courroie supporte l’effort de mesure prescrit

 

межосевое расстояние

 

Самое короткое расстояние между осями двух синхронных шкивов, когда ремень находится под требуемым натяжением

 

 

3 Definitions relating to synchronous belts

 

 
concernant les courroies synchrones
 

Определения, относящиеся к синхронным ремням

 

 

 

 

 

3.1 Belts, general

 

Courroies,
 

Ремни, общая часть

 

 

 

3.1.1 synchronous belt

 

A belt, the cross section of which is in the general form of a rectangle, but with transverse teeth extending from the lower base at regularly spaced intervals

 

courroie synchrone

 

Courroie dont la section droite
la forme
d’un rectangle mais qui comporte
des intervalles
des dents transversales sous sa face
 

 

синхронный ремень

 

Ремень, прямое сечение которого имеет форму прямоугольника, на внутренней стороне которого расположены на равном расстоянии друг от друга поперечные зубья трапециевидного профиля

 

3.1.2 belt pitch

 

The linear distance between the axes of two consecutive teeth in a section of belt loaded to the prescribed measuring force

 

pas

 

Distance entre les axes de
de deux dents
dans une portion rectiligne de courroie supportant l’effort prescrit de mesure
 

 

шаг

 

Расстояние между осями симметрии двух последовательных зубьев на прямолинейном участке ремня, находящемся под заданным натяжением

 

 

3.1.3 pitch line

 

 

Any circumferential line in the belt which keeps the same length when the belt is bent perpendicularly to its base

 

ligne primitive

 

Toute ligne
de courroie qui conserve sa longueur lorsque la courroie est
perpendiculairement
sa base
 

 

расчетная линия

 

Любая круговая линия ремня, сохраняющая свою длину, когда ремень сложен перпендикулярно к основанию

 

 

3.1.4 pitch length longueur primitive

 
The length of the pitch line of a belt Longueur
de la ligne primitive d’une courroie
 

 

 

расчетная длина

 

Развернутая длина расчетной линии ремня

 

3.1.5 width

 

The transverse dimension of the belt that can be used to transmit power

 

largeur

 

Dimension transversale de la courroie dont
la puissance transmissible
 

 

 

ширина

 

Поперечный размер ремня, от которого зависит передаваемая мощность

 

3.1.6 height

 

The total height of the belt

 

hauteur

 

Hauteur ou
totale de la courroie
 

 

высота

 

Высота или общая толщина ремня

 

 

3.2 Synchronous belt teeth

 

 

 

 

 

Dents de courroie synchrone

 

 

 

Зубья синхронного ремня

 

 

 

3.2.1 tooth

 

 

One of the transverse elements protruding from the bottom of the belt having the profile to mesh with the teeth in a synchronous pulley

 

 

dent

 

Un des
transversaux faisant saillie sous la face
de la courroie et ayant Ie profil pour engrener avec les dents d’une poulie synchrone
 

 

зубья

 

Поперечные элементы, расположенные на внутренней поверхности ремня, для сцепления с зубьями синхронного шкива

 

3.2.2 tip line

 

 

Line joining the apices of the belt teeth

 
ligne de
 

 

Ligne joignant les sommets de dents d’une courroie
l’ахе longitudinal de celle-ci
 

 

верхняя линия

 

Линия, соединяющая вершины зубьев ремня параллельно его продольной оси

 

 

3.2.3 root line

 

 

Line joining the low points between the teeth of a belt

 

ligne de pied

 

Ligne joignant les bases de dents d’une courroie
l’axe longitudinal de celle-ci
 

 

нижняя линия

 

Линия, соединяющая основания зубьев ремня параллельно его продольной оси

 

 

3.2.4 tooth height

 

Distance between the tip line and the root line

 

hauteur de dent

 

Distance comprise entre une ligne de
et une ligne de pied pour une
courroie, ces deux lignes
dans la
section droite longitudinale de la courroie
 

 

высота зубьев

 

Расстояние между верхней и нижней линиями одного зуба, расположенными на одном и том же продольном прямом сечении ремня

 

3.2.5 flank

 

 

Area defined by the width of the belt and the straight portion of the tooth section contained between the tip line and the root line

 

flanc

 

Surface
par la largeur de la courroie et la partie rectiligne de la dent comprise entre la ligne de
et la ligne de pied
 

 

боковая поверхность

 

 

Участок, образующийся между внутренней и наружной поверхностями

 

 

3.2.6 mating flank

 

 

Flank of the belt tooth that is in contact with the pulley tooth

 

 

flanc en contact

 

Celui des deux flancs de la dent d’une courroie qui touche une dent de poulie

 

боковая контактирующая поверхность

 

Боковая поверхность зуба ремня, которая соприкасается с зубом шкива

 

3.2.7 working flank

 

 

Flank of a belt tooth used to transmit motion to or from the pulley

 

flanc actif

 

Celui des deux flancs d’une dent de courroie qui recoit Ie mouvement ou Ie transmet
une poulie
 

 

активная боковая поверхность

 

Та из двух боковых поверхностей зуба ремня, которая передает движение шкиву или принимает от шкива

 

 

3.2.8 non-working flank

 

 

Flank of tooth opposite the working flank

 

flanc inactif

 

Flanc d’une dent de courroie
au flanc actif
 

 

неактивная боковая поверхность

 

Другая боковая поверхность того же зуба

 

3.2.9 radius at tooth tip

 

Radius of a curve connecting the tooth flank with the tip line

 
rayon en
de dent
 

 

Rayon de l’arrondi reliant la section d’un flanc de dent
sa ligne de
 

 

радиус в верхней части зуба

 

Радиус закругленной части, соединяющий сечение боковой поверхности зуба с его верхней линией

 

 

3.2.10 radius at tooth root

 

Radius of a curve connecting the tooth flank witn the root line

 

rayon au pied de dent

 

Rayon de l’arrondi reliant la section d’un flanc de dent
sa ligne de pied
 

 

радиус у основания зуба

 

Радиус закругленной части, соединяющей сечение боковой поверхности зуба с его нижней линией

 

 

3.2.11 width at tooth root

 

Linear distance between the theoretical points of intersection of the tooth flanks with the root line when the belt is straight

 

largeur au pied de dent

 

 

 

Distance comprise entre les points
d’intersection des flancs d’une dent avec sa ligne de pied, lorsque la portion
de la courroie est rectiligne
 

 

 

ширина у основания зуба

 

 

 

Расстояние между теоретическими точками пересечения боковых поверхностей зуба с его нижней линией, когда рассматриваемый участок ремня прямолинейный

 

3.2.12 tooth angle

2
 

Included angle between the flanks of the belt tooth

 

angle de dent

 

 

Angle compris entre les deux flancs d’une dent de courroie

 

угол зуба

 

 

Угол между обеими боковыми поверхностями зуба ремня

 

4 Definitions relating to synchronous pulleys

 

 
concernant les poulies synchrones
 

Определения, относящиеся к синхронным шкивам

 

 

 

 

 

 

 

4.1 Pulleys, general

 

Poulies,
 

Шкивы, общая часть

 

 

 

 

 

 

4.1.1 synchronous pulley

 

 

Pulley with transverse teeth equally spaced around its circumference

 

poulies synchrone

 

 

Poulie munie
sa
de dents transversales
 

 

синхронный шкив

 

 

Шкив, имеющий на своей окружности поперечные равноотстоящие зубья

 

 

4.1.2 pitch reference cylinder

 

 

 

Imaginary cylindrical surface, coaxial to a pulley, with reference to which the dimensions of the tooth space of a pulley are defined

 

cylindre primitif

 

 

Cylindre de
fictif, coaxial
la poulie, et servant   
les cotes des dents de la poulie et de leurs intervalles
 

 

расчетная цилиндрическая поверхность

 

 

Воображаемая цилиндрическая поверхность, соосная со шкивом и служащая для определения размеров зубьев шкива и расстояния между ними*

 

________________

* См. 4.2.2 для определения расстояния между зубьями.

 

4.1.3 pitch circle

 

 

Section of a pitch reference cylinder with a plane perpendicular to the axis of the pulley

 

 

cercle primitif

 

Section du cylindre primitif par un plan perpendiculaire
l’axe de la poulie
 

 

расчетная окружность

 

Сечение расчетной поверхности с плоскостью, перпендикулярной к оси шкива

 

4.1.4 outside diameter

 

Diameter of the tip circle

 
 

 

 
du cercle de
 

 

наружный диаметр

 

Диаметр верхней окружности*

 

________________

* Cм. 4.2.4 для определения верхней окружности.

 

4.1.5 pitch diameter

 

Diameter of the pitch circle

 
 
primitif
 

 

du cercle primitif
 

 

расчетный диаметр

 

Диаметр расчетной окружности

 

4.1.6 pitch line differential

 

Radial distance between the pitch circle and the tip circle

 
 
de ligne primitive
 

 

Distance
suivant un rayon entre Ie cercle primitif et Ie cercle de
 

 

положение расчетной линии

 

Расстояние, измеренное по радиусу между расчетной окружностью и верхней окружностью

 

4.1.7 pitch

 

Length of arc on the pitch circle contained between two consecutive corresponding profiles

 

 

pas

 

Longueur Ie l’arc du cercle primitif compris entre les points homologues de deux dents
 

 

шаг*

 

Длина дуги расчетной окружности между соответствующими точками двух последовательных зубьев

 

________________

* Рассматриваемый как отрезок зубчатой рейки, шаг шкива соответствует шагу ремня.

 

4.1.8 minimum pulley width

 
 

Smallest lateral distance across the face of a pulley (or between the flanges of a flanged pulley) that can be used for a stated belt width

 

largeur minimale de poulie

 

Plus petite distance axiale entre les deux faces d’une poulie, ou entre les flasques d’une poulie
, qui puisse
pour une courroie de largeur
 

 

 

 

минимальная ширина

 

 

Наименьшее осевое расстояние между обеими поверхностями шкива или между фланцами шкива, которое может быть использовано для ремня заданной ширины

 

 

4.1.9 measuring pulley

 

 

Pulley specifically machined or selected to permit precise length measurement of a synchronous belt

 

 

poulie de mesure

 

 

Poulie
ou choisie
 pour permettre de mesurer avec
la longueur d’une courroie synchrone
 

 

 

измерительный шкив

 

 

Изготовленный или специально подобранный шкив для прецизионного измерения длины синхронного ремня

 

 

4.1.10 measuring pulley tooth clearance

 

Shortest distance between nonworking flanks of belt and measuring pulley teeth, when the working flanks are in contact

 

jeu de denture sur la poulie de mesure

 

 

Plus petite valeur de la distance
les flancs inactifs d’une dent de la courroie et de la dent voisine de la poulie, lorsque les flancs actifs sont en contact l’un avec l’autre
 

 

зубчатый зазор на измерительном шкиве

 

 

Наименьшее расстояние, разделяющее неактивные боковые поверхности зуба ремня и зуба шкива, когда активные боковые поверхности контактируют друг с другом

 

4.2 Synchronous pulley teeth

 

Dents de poulie synchrone

 

Зубья синхронного шкива

 

 

 

 

 

 

4.2.1 teeth

 

 

Equally spaced transverse protrusions with which the belt teeth mesh to provide a transfer of force between the belt and the pulley

 

dents

 

 

 
transversaux
 
 
qui font saillie
la
d’une poulie et avec lesquels les dents d’une courroie
pour transmettre un effort tangential de l’une
l’autre
 

 

зубья

 

 

Равностоящие поперечные элементы, выступающие на окружности шкива, с которыми зубья ремня образуют зацепление для передачи тангенциального усилия

 

 

4.2.2 tooth space

 

 

Space between two adjacent teeth of a pulley

 

intervalle

 

Intervalle entre deux dents
d’une poulie
 

 

пространство между зубьями

 

Расстояние между двумя последовательными зубьями шкива

 

4.2.3 tip cylinder

 

 

Surface coaxial with the pulley containing the crests of the teeth

 

 

cylindre de
 

 

Surface coaxiale a la poulie et contenant les sommets ou
de dents
 

 

верхняя цилиндрическая поверхность

 

Поверхность, соосная со шкивом на уровне вершин зубьев

 

4.2.4 tip circle

 

 

Section of the tip cylinder whose plane is perpendicular to the axis of the pulley

 

 

cercle de
 

 

Section droite du cylinder de
 

 

верхняя окружность

 

Прямое сечение верхней цилиндрической поверхности

 

4.2.5 root cylinder

 

 

Surface coaxial with the pulley containing the bottom of the tooth spaces

 

cylindre de pied

 

Surface coaxiale
la poulie et tangente au fond des intervalles
 

 

нижняя цилиндрическая поверхность

 

Поверхность, соосная со шкивом и касательная к основанию зубьев

 

4.2.6 root circle

 

 

Section of the root cylinder whose plane is perpendicular to the axis of the pulley

 

cercle de pied

 

Section droite du cylindre de pied

 

нижняя окружность

 

Прямое сечение нижней цилиндрической поверхности

 

4.2.7 tooth space depth

 

Radial distance between the tip circle and the root circle

 

 

profondeur de I’intervalle

 

Dimension
Ie long d’un rayon entre un cercle de
et un cercle de pied
dans Ie
plan
 

 

глубина пространства между зубьями

 

Расстояние, определяемое по радиусу между верхней и нижней окружностями, расположенными в одной плоскости

 

4.2.8 flank

 

 

Area defined by the width of the pulley and the involute (or straight) portion of a pulley tooth contained between the tip cylinder and the root cylinder

 

flanc

 

 

Une des surfaces
par la largeur de la poulie et par la partie en
de cercle (ou rectiligne) de la dent qui est comprise entre Ie cylinder de
et Ie cylindre de pied
 

 

боковая поверхность

 

Одна из поверхностей, ограниченных шириной шкива и верхней и нижней поверхностями цилиндра (или прямолинейными участками)

 

4.2.9 mating flank

 

 

Flank of the pulley tooth that is in contact with the belt

 

flanc en contact

 

Flanc d’une dent de poulie qui touche une dent de courroie

 

боковая контактирующая поверхность

 

Боковая поверхность зуба шкива, соприкасающаяся с зубом ремня

 

4.2.10 working flank

 

 

Flank of the pulley tooth used to transmit motion to or from the belt

 

flanc actif

 

Flanc d’une dent de poulie qui

 
Ie mouvement ou Ie transmet
la courroie
 

 

активная боковая поверхность

 

Боковая поверхность зуба шкива, передающая движение ремню или принимающая его

 

4.2.11 non-working flank

 

 

Flank of the pulley tooth opposite the working flank

 

flanc inactif

 

Flanc d’une dent de poulie
au flanc actif
 

 

неактивная боковая поверхность

 

Другая боковая поверхность того же зуба

 

4.2.12 radius at the tooth tip

 

Radius of a curve connecting the tooth flank with the tip circle

 
rayon en
de dent
 

 

Rayon de l’arrondi reliant la section d’un flanc de dent a sa ligne de
 

 

радиус у вершины зуба

 

Радиус закругления, соединяющего сечение боковой поверхности зуба с верхней окружностью

 

4.2.13 radius at the tooth root

 

Radius of a curve connecting the tooth flank with the root circle

 

rayon au pied de dent

 

Rayon de l’arrondi reliant la section d’un flanc de dent
sa ligne de pied
 

 

радиус у основания

 

Радиус закругления, соединяющего сечение боковой поверхности зуба с нижней окружностью

 

 

 

4.2.14 width at tooth space root

 

Linear distance between the theoretical points of intersection of the tooth space flanks with the root circle

 

largeur au pied de dent

 

Distance
suivant une corde entre les points
d’intersection du cercle de pied avec les flancs, se faisant face, de deux dents
 

 

ширина основания зуба

 

Расстояние, измеренное по хорде между теоретическими точками пересечения нижней окружности с боковыми поверхностями, расположенными напротив двух соседних зубьев

 

4.2.15 tooth space angle

2
 

Included angle between the flanks of the tooth space

 

angle au sommet de l’intervalle

 

Angle compris entre les flancs, se faisant face, de deux dents
 

 

угол пространства между зубьями

 

Угол между боковыми поверхностями двух соседних зубьев

 

 

4.3 Synchronous pulley involute tooth generating tools

 

  
de
pour dents de poulie en
 

Стандартная кремальера для зубьев шкива в развертке

 

 

 

 

 

4.3.1 rack

 

Toothed member having the form of a rectangular bar, whose teeth may be superimposed by rectilinear translation

 
 

 

 

Organe de forme

, et portant sur
 
une de ses faces une
de dents superposables par translation rectiligne
 

 

кремальера

 

Элемент в форме параллелепипеда, несущий на одной из своих поверхностей ряд одинаковых равноотстоящих зубьев

 

4.3.2 reference rack

 

 

Rack whose profile is used as the base of a standardized system of pulleys having the same generating rack

 

 
de
 

 

  
dont la section perpendiculaire aux
des dents sert
les dimensions
des dents en
d’un
de poulies
 

 

эталонная кремальера

 

 

Вымышленная кремальера, сечение которой перпендикулярно к ребрам зубьев и служит для определения нормализованных размеров зубьев в развертке той же системы шкивов

 

 

4.3.3 reference rack: pitch line

 

 

Line, with reference to which the dimensions of the rack teeth are defined

 

ligne primitive de la  

 
de
 

 

Ligne par rapport a laquelle sont
les dimensions des dents de la
de
 

 

расчетная линия эталонной кремальеры

 

Линия, по отношению к которой определяются размеры зубьев эталонной кремальеры

 

4.3.4 reference rack: root line

 

 

Line joining the low points between the teeth of a rack

 
ligne de pied de la
 
de
 

 

Ligne reliant les fonds des dents d’une section longitudinale de la

 

 

нижняя линия эталонной кремальеры

 

Линия, соединяющая поверхности кремальеры, расположенные между зубьями, в продольном сечении эталонной кремальеры

 

4.3.5 reference rack: tip line

 

 

Line joining the tips of the teeth of a rack

 
ligne de
de la
de
 

 

Ligne reliant les
des dents d’une section longitudinale
 
de la
 

 

верхняя линия эталонной кремальеры

 

Линия, соединяющая верхние поверхности зубьев, в продольном сечении эталонной кремальеры

 

 

4.3.6 reference rack: flank

 

 

Portion of the rack tooth contained between the tip line and the root line

 

flanc d’une dent de la

 
de
 

 

Partie d’une dent de la

 
de
qui est comprise entre la ligne de
 

et la ligne de pied

 

боковая поверхность зуба эталонной кремальеры

 

Часть зуба эталонной кремальеры между уровнем верхней и нижней линии

 

4.3.7 reference rack: pitch line location

 

Distance between the pitch line and the root line of the rack

 
 
de la ligne primitive de la
  de
 

 

Distance comprise entre la ligne primitive de la
de
et sa ligne de pied
 

 

расположение расчетной линии эталонной кремальеры

 

Расстояние между расчетной линией эталонной кремальеры и нижней линией

 

4.3.8 reference rack: pitch

 

Linear distance between the centre of two adjacent teeth on the rack

 
pas de la
 de
 

 

Distance comprise entre les axes de
de deux dents
de la  
 
de
 

 

шаг эталонной кремальеры

 

Расстояние между осями симметрии двух последовательных зубьев эталонной кремальеры

 

4.3.9 reference rack: tooth angle

2
 

Included angle between the flanks of the tooth of the rack

 

angle de la dent de la

 
de
 

 

Angle
par les deux flancs d’une
dent de la
 
  
de
 

 

угол у вершины зуба эталонной кремальеры

 

Угол между двумя боковыми поверхностями зуба эталонной кремальеры

 

4.3.10 reference rack: tooth height

 

Distance between the tip line and the root line of the rack

 

hauteur de dent de la

  
de
 

 

Distance comprise entre une ligne de
et une ligne de pied
dans la
section droite longitudinale de la
 
 
de
 

 

высота зуба эталонной кремальеры

 

Расстояние между верхней и нижней линиями, расположенными в одном и том же прямом продольном сечении эталонной кремальеры

 

4.3.11 reference rack: width at tooth tip

 

Linear distance between the theoretical points of intersection of the tooth flanks with the tip line of the rack

 
largeur en
de dent de la
de
 

 

Dans une section droite longitudinale de la
de
, distance comprise entre les points
d’intersection des flancs d’une dent avec la ligne de
 

 

ширина в верхней части зуба эталонной кремальеры

 

Расстояние между теоретическими точками пересечения боковых поверхностей зуба с верхней линией в прямом продольном сечении кремальеры

 

4.3.12 reference rack: radius at tooth tip

 

Radius of a curve connecting the tooth flank with the tip line of the rack

 
rayon en
d’une dent de la
 de
 

 

Dans une section droite longitudinale de la  
 de
, rayon de l’arrondi reliant un flanc de dent
la ligne de
 

 

радиус в верхней части зуба эталонной кремальеры

 

 

Радиус закругления, соединяющего боковую поверхность зуба с верхней линией в прямом продольном сечении эталонной кремальеры

 

4.3.13 reference rack: radius at tooth root

 

Radius of a curve connecting the tooth flank with the root line of the rack

 
rayon au pied d’une dent de la
  de
 

 

Dans une section droite longitudinale de la
de
, rayon de l’arrondi reliant un flanc de dent
la ligne de pied
 

 

радиус у основания зуба эталонной кремальеры

 

Радиус закругления, соединяющего боковую поверхность зуба с нижней линией в прямом продольном сечении эталонной кремальеры

 

 

 

      

     

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА АНГЛИЙСКОМ ЯЗЫКЕ

 

 

В

Belt pitch

3.1.2

Belts

3.1

С

Centre distance

2.2

F

Flank

3.2.6, 4.2.8

Н

Height

3.1.6

М

Mating flank

3.2.6, 4.2.9

Measuring pulley

4.1.9

Measuring pulley tooth clearance

4.1.10

Minimum pulley width

4.1.8

N

Non-working flank

3.2.8, 4.2.11

О

Outside diameter

4.1.4

Р

Pitch

4.1.7

Pitch circle

4.1.3

Pitch diameter

4.1.5

Pitch length

3.1.4

Pitch line

3.1.3

Pitch line differential

4.1.6

Pitch reference cylinder

4.1.2

Pulleys

4.1

R

Rack

4.3.1

Radius at tooth line

 4.2.12

Radius at tooth root

3.2.10

Radius at tooth tip

3.2.9, 4.2.12

Reference rack

4.3.2

flank

 

4.3.6

pitch

 

4.3.8

pitch line

 

4.3.3

pitch line location

 

4.3.7

radius at tooth tip

 

4.3.12

radius at tooth root

 

4.3.13

root line

 

 4.3.4

tip line

 

4.3.5

tooth angle

 

4.3.9

tooth height

 

4.3.10

width at tooth tip

 

4.3.11

Root circle

4.2.6

Root line

3.2.3

S

Synchronous belt

3.1.1

Synchronous belt drive

2.1

Synchronous pulley

4.1.1

Synchronous pulley teeth

4.2

Synchronous pulley involute tooth generating tools

4.3, 3.2

Т

Tip circle

4.2.4

Tip cylinder

4.2.3

Tip line

3.2.2

Teeth

4.2.1

Tooth

3.2.1

Tooth angle

3.2.12

Tooth height

3.2.4

Tooth space

4.2.2

Tooth space angle

4.2.15

Tooth space depth

4.2.7

W

Width

3.1.5

Width at tooth root

3.2.11

Width at tooth space root

4.2.14

Working flank

3.2.7, 4.2.10

 

 

      

     

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ФРАНЦУЗСКОМ ЯЗЫКЕ

 

 

А

angle au sommet de l’intervalle

4.2.15

angle de dent

3.2.12

angle de la dent de la  
 de
 

4.3.9

С

cercle de pied

4.2.6

cercle de
 

4.2.4

cercle primitif

4.1.3

courroies

3.1

courroie synchrone

3.1.1

 

 

4.3.1

 de
 

4.3.2

de
pour dents de poulie en
 

4.3

cylindre de pied

4.2.5

cylindre de
 

4.2.3

cylindre primitif

4.1.2

D

 

4.1.4

primitif
 

4.1.5

dent (s)

3.2.1, 4.2.1

dents de courroie synchrone

3.2

dents de poulie synchrone

4.2

de ligne primitive de la
de
 

4.3.7

de la ligne primitive
 

4.1.6

Е

entr’axe

2.2

F

flanc

3.2.5, 4.2.8

flanc actif

3.2.7, 4.2.10

flanc d’une dent de la
de
 

4.3.6

flanc en contact

3.2.6, 4.2.9

flanc inactif

3.2.8, 4.2.11

H

hauteur

3.1.6

hauteur de dent

3.2.4

hauteur de dent de la
de
 

4.3.10

I

intervalle

4.2.2

J

jeu de denture sur la poulie de mesure

4.1.10

L

largeur

3.1.5

largeur au pied de dent

3.2.10, 4.2.14

largeur en
de dent de la
de
 

4.3.11

largeur minimale de poulie

4.1.8

ligne de pied

3.2.3

ligne de pied de la
de
 

4.3.4

ligne de
 

 3.2.2

ligne de
de la
de
 

4.3.5

ligne primitive

3.1.3

ligne primitive de la
de
 

4.3.3

P

pas

3.1.2, 4.1.7

de la
de
 

4.3.8

poulies

4.1

poulie de mesure

4.1.9

poulie synchrone

4.1.1

profondeur de l’intervalle

4.2.7

R

rayon au pied de dent

3.2.10, 4.2.13

rayon en
de dent
 

3.2.9, 4.2.12

rayon au pied d’une dent de la
de
 

4.3.13

rayon en
d’une dent de la
de
 

4.3.12

Т

transmission par courroie synchrone

2.1

 

 

      

     

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА РУССКОМ ЯЗЫКЕ

 

 

зубья синхронного ремня

3.2, 3.2.1

боковая поверхность

 

3.2.5

боковая поверхность активная

 

3.2.7

боковая поверхность контактирующая

 

3.2.6

боковая поверхность неактивная

 

3.2.8

верхняя линия

 

3.2.2

высота зубьев

 

3.2.4

нижняя линия

 

3.2.3

радиус в верхней части зуба

 

3.2.9

радиус у основания зуба

 

3.2.10

угол зуба

 

3.2.12

ширина у основания зуба

 

3.2.11

зубья синхронного шкива

4.2, 4.2.1

боковая поверхность

 

4.2.8

боковая поверхность активная

 

4.2.10

боковая поверхность контактирующая

 

4.2.9

боковая поверхность неактивная

 

4.2.11

верхняя цилиндрическая поверхность

 

4.2.3

верхняя окружность

 

4.2.4

глубина пространства между зубьями

 

4.2.7

пространство между зубьями

 

4.2.2

радиус у вершины зуба

 

4.2.12

радиус у основания

 

4.2.13

ширина основания зуба

 

4.2.14

угол пространства между зубьями

 

4.2.15

К

кремальера

4.3.1

боковая поверхность зуба эталонной кремальеры

 

4.3.6

верхняя линия эталонной кремальеры

 

4.3.5

высота зуба эталонной кремальеры

 

4.3.10

нижняя линия эталонной кремальеры

 

4.3.4

радиус в верхней части зуба эталонной кремальеры

 

4.3.12

радиус у основания зуба эталонной кремальеры

 

4.3.13

расчетная линия эталонной кремальеры

 

4.3.3

расположение расчетной линии эталонной кремальеры

 

4.3.7

угол у вершины зуба эталонной кремальеры

 

4.3.9

шаг эталонной кремальеры

 

4.3.8

ширина в верхней части зуба эталонной кремальеры

4.3.11

эталонная

 

4.3.2

Р

расстояние межосевое

2.2

ремни

3

высота

 

3.1.6

зубья синхронного ремня

 

3.2

общая часть

 

3.1

расчетная длина

 

3.1.4

расчетная линия

 

 3.1.3

синхронные

 

3.1.1

шаг

 

3.1.2

ширина

 

3.1.5

 С

синхронная ременная передача

2.1

синхронные ремни

3

Ш

шкивы

4.1

зубчатый зазор на измерительном шкиве

 

4.1.10

зубья синхронного шкива

 

4.2

измерительный шкив

 

4.1.9

минимальная ширина

 

4.1.8

наружный диаметр

 

4.1.4

расчетный диаметр

 

4.1.5

расчетная окружность

 

4.1.3

расчетная цилиндрическая поверхность

 

4.1.2

синхронные

4.1.1

 

 

      

     

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА НЕМЕЦКОМ ЯЗЫКЕ

 

 

А

Arbeitsflanke

3.2.7, 4.2.10

 

4.1.4

В

Bezugsprofil

4.3.2

Bezugszahnstange

4.3.2

Breite

3.1.5

Breite am
 

3.2.11

Breite am Zahnkopf

4.3.11

Breite am
 
 

4.2.14

F

Flanke

3.2.5, 4.2.8, 4.3.6

Hankenspiel in der
 

4.1.10

 

4.2.6

 

3.2.3, 4.3.4

 

4.2.5

G

Gegenflanke

3.2.6, 4.2.9

H

 

3.1.6

К

Kopfkreis

4.2.4

Kopflinie

3.2.2, 4.3.5

Kopfzylinder

4.2.3

L

Lage der Wirklinie

4.3.7

M

 

4.1.9

Mittenabstand

2.2

R

Radius am
 

3.2.10, 4.2.13, 4.3.13

Radius am Zahnkopf

3.2.9, 4.2.12, 4.3.12

Riemen

3.1

Riemenzahnteilung

3.1.2

 

3.2.8, 4.2.11

S

Scheibe

4.1

Scheibenbreite, Mindest

4.1.8

Synchronriemen

3.1.1

Synchronriementrieb

2.1

Synchronscheibe

4.1.1

Т

Teilung

4.1.7, 4.3.8

Teilungs-Bezugszylinder

4.1.2

W

Wirkdurchmesser

4.1.5

Wirkkreis

4.1.3

 

3.1.4

Wirklinie

3.1.3, 4.3.3

Wirklinien-Differenz

4.1.6

Z

Zahn

3.2.1, 4.2.1

 

3.2.4, 4.3.10

 

4.2.2

 

4.2.7

 

4.2.15

Zahnstange

4.3.1

Zahnteilung

3.1.2, 4.1.7

Zahnwinkel

 3.2.12, 4.3.9

 

 

      

     

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ИТАЛЬЯНСКОМ ЯЗЫКЕ

 

 

А

altezza

3.1.6

altezza del dente

3.2.4, 4.3.10

angolo del dente

3.2.12, 4.3.9

angolo del vano

4.2.15

С

cerchio di fondo

4.2.6

cerchio di troncatura

4.2.3, 4.2.4

cilindro di fondo

4.2.5

cilindro primitivo di riferimento

4.1.2

cinghie,
 

3.1

cinghia sincrona

3.1.1

circonferenza primitiva

4.1.3

cremagliera

4.3.1, 4.3.2

D

dente

3.2.1, 4.2.1

dentatura cinghia sincrona

3.2

dentatura puleggia sincrona

4.2

diametro esterno

4.1.4

diametro primitivo

4.1.5

F

fianco

3.2.5, 4.2.8, 4.3.6

fianco attivo

3.2.7, 4.2.10

fianco a contatto

3.2.6, 4.2.9

fianco inattivo

3.2.8, 4.2.11

G

cremagliera di riferimento per dentatura puleggia ad evolvente

4.3

gioco nella dentatura delle puleggia di misura

4.1.10

L

larghezza

3.1.5

larghezza sul fondo del dente

3.2.11

larghezza alla
del dente
 

4.3.11

larghezza minima

4.1.8

larghezza sul fondo del vano

4.2.14

linea di fondo

3.2.3, 4.3.4

linea di troncatura

3.2.2, 4.3.5

linea primitiva

3.1.3, 4.3.3

lunghezza primitiva

3.1.4

Р

passo

3.1.12, 4.1.7, 4.3.8

pulegge

 4.1

puleggia di misura

4.1.9

puleggia sincrona

4.1.1

del vano
 

4.2.7

posizione linea primitiva

4.3.7

Q

quota radiale primitiva

4.1.6

R

raccordo alla
del dente
 

3.2.9, 4.2.12, 4.3.12

raccordo sul fondo del dente

3.2.10, 4.2.13, 4.3.13

V

vano

4.2.2

 

     

     

     

 

ГОСТ 28505-90

Шкурки бобра речного выделанные. Технические условия

ГОСТ 28506-90

Сборки тепловыделяющие ядерных энергетических реакторов типа ВВЭР. Методы контроля герметичности оболочек тепловыделяющих элементов

ГОСТ 28507-99

Обувь специальная с верхом из кожи для защиты от механических воздействий. Технические условия

ГОСТ 28515-97

Медь. Метод испытания проб на удлинение спирали

ГОСТ 28517-90

Контроль неразрушающий. Масс-спектрометрический метод течеискания. Общие требования